The flight weight is only 62.5 grams!It is currently the smallest and lightest brushless 2S quad-axis on the market. The flight control board uses OVERSKY NAZE 32 flight control board and has three built-in compatible receivers: 1) compatible with DSMX/DSM2, 2) compatible with FlySky, 3) compatible with Futaba SFHSS.
Super-X V2 is improved on the basis of the first generation Super-X.In response to users' feedback on Super-X, we have made the following improvements to Super-X V2: 1) The output shaft of the brushless motor is replaced with 1.5mm and the paddle with a 1.5mm mounting hole; 2) The installation of flight control has been completely simplified (small screws and copper sleeves are no longer used); 3) The design of split frames is adopted; 4) The USB function is integrated on the aircraft control board.
The improved Super-X V2 remains one of the smallest and lightest brushless multi-axle aircraft available today.It is paired with a 32X flight control panel and is equipped with 4 miniature brushless power groups that can provide more than 2 times the weight of the flight, which allows it to easily achieve actions such as air rolling or install FPV equipment.And its small size makes it completely free to fly indoors.
Super-X V2 features:
1)Wheelbase: 125mm;
2)Weight: 62.5g (including 2S 300mAh battery);
3)Pad diameter: 75mm;
4)Motor model: MP-03 (3g, KV4000);
5)Electrical adjustment model: MU-3A arm type electric regulation or MP-7A arm type electric regulation;
6)Flight control board: Scisky 32-X (with three optional compatible receivers, supporting Baseflight and Claenflight firmware);
Scisky 32-X flight control features
characteristic:
1) Ultra-small size (excluding shell)
2) Ultra-light weight (excluding shell and built-in receiver): 3.2g (type A), 2.9g (type B);
3) Working voltage: Type X: 3.3~4.5V or 5~10VItems
4) 12M/10PPM crystal oscillator;
5) Support receiver signal type: DSMX/DSM2 or FUTABA SFHSS RX
6) Optionally compatible with DSMX/DSM2 or FUTABA SFHSS receivers
7) The X-type built-in DCDC boost circuit (output 5V/500mA) can power external devices;
8) Independent IIC, GPS, PPM/DSM/SBUS receiver interfaces;
Note: The X-type is a 1.5mm pitch terminal.
Instructions for indicator lights:
Red ---Power Indication; Blue ---Flight Mode Indication; Green ---Unlock Indication;
Receiver wiring method:
XThe model has an RX-S interface (1.25mm 3P) dedicated to external receivers. This interface supports PPM, DSM2/DSMX, SBUS (Note 1) signal input, and also supports 3.3V or VIN output (Note 2). Users can short-circuit the pads of the RX-S interface and modify the receiver type in the GUI to achieve various external receivers.Type X supports compatible with DSMX/DSM2 or FUTABA SFHSS receivers
Note: 1), the X-type supports signal inversion;
2) When the output is VIN, and VIN>When 5.5V, please first confirm whether the external receiver supports operating voltages of 5.5V or above, otherwise the external receiver may burn;
3) Even if there is already a built-in receiver, if the built-in receiver is set to prohibit output (the built-in receiver RF circuit does not work at this time), the external receiver can also be used;
Flight requirements:
1)When using a built-in receiver, it is necessary to support DSM2 protocol, FlySky protocol, SFHSS four-way or higher transmitter or high-frequency head; when using an external receiver, it is necessary to use a corresponding 4-way receiver and transmitter;
2)Charger that supports 2S lithium battery;
Frequency operation
1. Press and hold the frequency switch on the receiver and power on the Scisky 32-X flight control board, then release the frequency switch. At this time, connect it.
The green LED flashes on the receiver (the receiver enters the frequency matching mode);
2. Press and hold the frequency switch of the upper receiver and turn on the power supply;
3. When the green LED on the receiver changes from flash to non-light and then becomes constant, it means that the frequency is successful, otherwise repeat the above steps.
Package content 2S version:
1)Super-X V2 rack set;
2)4 brushless motors of MP-03; one Oversky 32 2S X flight control board
3)4 arm type brushless electric regulators;
4)1 2S 300mah/25C battery;
5)8 75mm paddles (2 sets, paddles are not in the picture below);
6)A tie.
